ISO 17025 accredited calibration laboratory +49 7245 80475-0 info@inotech.eu
Home/Products/Domestic water meter test system

Domestic water meter test system for assembly, laboratory and network

Test and calibration systems for domestic water meters of all measuring principles – with piston, twin-piston, gravimetric or volumetric reference system.

Water meter test rig with clamping system
MEASURING RANGE
1 l/h – 30 m³/h
MEASUREMENT UNCERTAINTY
< 0.1 %
TEST POSITIONS
1 – 40
NOMINAL SIZES
DN 15 – DN 50

What the system delivers

Gravimetric reference systems are typically used, and for cost reasons volumetric systems as well. If large quantities of identical water meters are to be calibrated, the piston or twin-piston system is the best choice. It can calibrate more than 200 meters per hour.

The systems can be designed for cold or hot water. Their modular concept allows them to be adapted to the available space. Measurement uncertainties better than 0.1 % can be achieved!

Meter communication takes place via interfaces to smart meters or by optical scanning for mechanical water meters. After meter clamping, the test sequences with venting, flushing and measurement are automated.

The systems are used by meter manufacturers, water utilities, verification bodies and accredited calibration laboratories.

Scope of supply
Test frame with automatic meter clamping
Reference system (piston, twin-piston, gravimetric or volumetric)
Flow and pressure control
Optical or electronic register reading
Operator station with inotech test software and database
Flushing and venting system
Water meter test positions with optical detection
TEST POSITIONS WITH OPTICAL REGISTER READING
Volumetric test rig with reference vessel
Approval measurement with reference device
Displays of a water meter test rig
TEST POSITION DISPLAYS AND READING

From single calibration to series testing

Four reference principles

Gravimetric, volumetric, piston, twin-piston – matched to test throughput, measuring range and measurement uncertainty.

Meter connection

Communication with smart meters or optical scanning of mechanical registers.

Fastest test system

The twin-piston system tests without a reset pause and significantly shortens the cycle time.

Smart meter ready

Readout and parameterisation via serial meter communication.

All meter measuring principles

Vane wheel, piston, ultrasonic and electromagnetic meters on one system.

Testing to MID, OIML and GM-P 5.22

Test point sequences and error limits to MID, OIML R49 and national requirements.

Technical specification

VALUES DEPEND ON CONFIGURATION · BINDING IN THE PROJECT DATA SHEET
Measuring range
1 l/h to 30 m³/h
Measurement uncertainty
< 0.1 %
Test positions
1 to 40, depending on nominal size and configuration
Nominal sizes
DN 15 to DN 50 (large water meters up to DN 300)
Reference system
Gravimetric, volumetric, piston, twin-piston
Test medium
Water, temperature-controlled
Meter types
Vane wheel, piston, ultrasonic and electromagnetic meters
Register reading
Optical, pulse, protocols
Standards
MID, OIML R49, GM-P 5.22, national test regulations
Software
inotech standard user interface, identical across all system types
Interfaces
ERP/MES integration, network, database and CSV export
Documentation
Test reports, calibration certificates, ISO 17025-capable traceability

Configuration and expansion

Temperature control

Control of water temperature for tests at defined operating points.

Pressure test

Integrated tightness and pressure resistance test in the same cycle.

Automated handling

Feeding and removal of meters via conveyor belts.

Retrofit

Modernisation of existing test rigs to current controls and software.

Do you have specific technical requirements?

Send us your specification – meter types, flow ranges, number of test positions and the required degree of automation.

A water meter test bench for all common apartment and domestic water meters

Whether apartment water meters in DN15 or domestic water meters up to DN50, inotech designs every water meter test bench around the meters that actually reach the test station in your operation. So that cold and hot water meters run under realistic conditions, you test each type with the appropriate medium. Heat meters, for which the temperature difference also counts, run on a dedicated heat meter test system. Whether the test water flows back in a circuit or the system works in once-through mode depends mainly on your local water supply. Scales, test vessels, electromagnetic flowmeters or pistons are available as the volume reference. The design is based on OIML, the European Measuring Instruments Directive MID and the requirements of the PTB (Physikalisch-Technische Bundesanstalt).

Where do you test your meters: on the assembly line, in the test room or directly at the house connection? This is where the three designs differ with which we cover the typical test tasks for domestic meters. The overview shows which water meter test bench suits which workflow.

ModelTest principleNominal sizesMeters per runTypical use
BPA7-2-5Piston prover, automaticDN15, DN20, DN25up to 5 or 8 in series, double test lineFinal test in meter assembly
RCA2300-Mvolumetric, manualup to DN50, up to 30 m³/h5 to 20 on two linesTest room with changing meter types
RAC-T5Reference water meter, portableDN15, DN20installed meter on siteChecks in the supply network

With a mixed meter population, a stationary water meter test bench in the test room can be combined with the portable device for checks in the network. Which combination pays off depends on how many meters you remove each year and how many you prefer to test in their installed state.

Changing on one line, testing on the other

If you assemble domestic water meters in series, the water meter test bench at the end of the line has to keep up with its cycle. Our BPA7-2-5 model, an automatic verification test bench for meter assembly lines, is built for exactly this. Its two test lines alternate: one measures while your staff swap the tested meters for new ones on the other. Clamping is thus taken out of the cycle time.

In the water meter piston test bench, the piston pushes a precisely known quantity of water through the row of meters with each stroke. As soon as the stroke is complete, the evaluation compares this quantity with the reading of each individual meter under test. Depending on the version, up to five or eight meters of nominal sizes DN15, DN20 or DN25 sit one behind the other.

The stainless steel drive piston is designed for more than half a million cycles. We guarantee this figure as long as the piston runs under normal operating conditions and is properly maintained by our service. A leakage sensor also monitors tightness. For meter manufacturers this means the water meter test bench withstands continuous operation over several shifts without the line coming to a standstill because of the test equipment.

Portable water meter test bench for testing directly at the installation site

If a household reports conspicuously high consumption, the question quickly arises whether the meter is measuring correctly. With the RAC-T5 model, you can clarify this on site. This portable water meter test bench tests domestic meters of nominal sizes DN15 and DN20 without having to remove them.

The hydraulic case contains a volumetric reference water meter through which the same water flow passes as through the meter under test. A cyclic sensor detects the installed meter, and the evaluation then calculates its deviation from the reference. The house connection remains closed. The result is available during the appointment. The test equipment thus travels to the meter, not the meter to the water meter test bench.

If you want to check your meter population regularly, the device also does a good job here. Just a few random samples show whether a particular year of manufacture or make is becoming conspicuous before the scheduled replacement is due. If a meter stands out, it goes to a water meter test bench in your workshop for closer examination.

ENAC-certified test vessels with an accuracy of 0.1 %

How accurately a volumetric water meter test bench measures depends first and foremost on its standard. In the RCA2300-M model, this task is performed by truncated-cone, graduated stainless steel test vessels on whose scale the test volume can be read. The Spanish accreditation body ENAC has certified them with an accuracy of 0.1 %. Verification bodies and calibration laboratories can thus keep the contribution of the standard to measurement uncertainty small and prove it.

Clamping is pneumatic; in the standard configuration, 5 to 20 meters sit on two lines. Adapter kits for the inlet and outlet side ensure that meters of different lengths fit into the lines. This water meter test bench is designed for meters up to DN50 (2 inches) and flow rates up to 30 m³/h, in a special version up to 40 m³/h. Special software calculates the error of each meter under test, and a portable handheld device brings the evaluation directly to the test station. Meters between DN50 and DN300 are additionally handled by our large water meter test bench with a scale as the main reference.

What results is water meter calibration in the true sense: the reading of the meter under test is compared with the standard and the deviation recorded. Verification, on the other hand, is decided solely by the competent authorities; our test benches provide the metrological basis for it. Worldwide, we have so far installed more than 1,000 test systems in more than 70 countries. This experience goes into every water meter test bench we design for your test task.

Modernise an older domestic water meter test system instead of replacing it

The mechanics of a test bench often outlast its control system by many years. If the computer, software or register detection of an older domestic water meter test system no longer suits your current meters, a new system is therefore not necessarily required. We specifically renew the parts that slow down operation: the mechanical structure, the PC or the software version. The system then works more efficiently and remains in use longer, without you having to re-plan the test room and water connection. This also applies to test benches from other manufacturers.

If capacity is no longer sufficient, we add further test stations to the water meter test bench. Because we guarantee ten years of spare parts supply for our systems, you plan your maintenance on a secure basis. You decide which services you obtain from us afterwards: maintenance according to a checklist, remote support or training for your staff can be agreed individually or in combination via our service for test systems.

Would you like to know whether your existing system can be modernised? Send us photos of the type plate, the number of test stations and a list of your meter types, ideally by email to info@inotech.eu. On this basis, our sales team compares modernisation and a new system in a free quotation.